professionalism in response
for expectations
Image is not available
knowledge and comptence
Image is not available
knowledge and laboratory condition for new products
Image is not available
CAREFULLY SELECTED COMPONENTS
Image is not available
timely delivery
Image is not available
previous arrowprevious arrow
next arrownext arrow
Slider

To meet your needs as a service provider focused on industrial markets, StickyStratum offers a range of services related to Hot-Melt coating and lamination in the following areas:

COATING AND LAMINATION HOT-MELT FITTING WITH SLOT HEADS

It is a contact method with coated material PSA, EVA, APAO adhesives. The method finds a wide range of applications in the industry where, first and foremost, the quality of the applied coating, i.e. its weight and smooth texture over the entire width of the intended coating, counts.

Benefits:

-the possibility of achieving different weights

-quality and stability of the applied adhesive film layer

-very good adhesion coefficient of elements glued together

- a process with a low service coefficient, resulting in a linearly reproducible effect of spreading on many production shares

- the possibility of applying a linear interrupt to obtain glue dots or dashed lines

- the possibility of using slit spacers with a specific geometry of overlap, i.e.

- obtaining the effect of deliberately interrupted lines on the coated material along its coating.


The range of coated materials are mainly plates and full rolls of material in roll-roll coating mode (optionally with gluing of anti-adhesive film)

 

COATING HOT-MELT TYPE WITH LINEAR FLOW HEADS

It is a non-contact method allowing the use of Hot-Melt adhesives in non-standard materials using adhesives PSA, EVA, APAO PUR. This method is a dedicated method for special applications and often finds a narrow application group. It allows you to create self-adhesive stabilization points, tapes, etc.

Benefits:

- the possibility of achieving different weights

- quality and stability of the applied layer of glue

- the ability to achieve a connection that maintains the permeability of the material (membranes, filters, etc.

- very good adhesion coefficient of elements glued together

- a process with a low service coefficient, resulting in a linearly reproducible effect of spreading on many production shares

- efficient process with an additional option of applying several adhesive lines to coated elements

- the possibility of applying glue on elements of different geometry, such as slats, angles etc.

- the possibility of applying a linear interrupt to obtain glue dots or dashed lines

The range of coated materials are mainly sections, ie angles, strips, but also membranes, insulating materials, floor mats, this method is also used in the production of automotive filters to join pleated ridges at specific and uninterrupted intervals.

 

COATING HOT-MELT TYPE WITH SPRAY HEADS

It is a method of applying the adhesive layer without contact of the head with the material, which allows working with materials that are poorly resistant to high temperatures, such as foils, polystyrenes etc. with material using adhesives PSA, EVA, APAO. This method is a method that finds application in less demanding glue applications and through its capabilities can be used on virtually any material available on the market.

Benefits:

- the possibility of achieving different weights

- quality and stability of the applied layer of glue with threadlike texture

- a process with a low service coefficient, resulting in a linearly reproducible effect of spreading on many production shares

- efficient and relatively fast process

- the possibility of applying glue on elements of different geometry, including multi-dimensional 3D elements

- the possibility of applying an adhesive film on perforated elements

- the possibility of using technology on both plates, roll-roll materials as well as on single shares of different and non-linear geometry

- a process that allows the breathing properties of the membrane material to be insulated with insulating materials

- the possibility of using materials with low thermal resistance

The range of coated materials is the most honest of those described above. The most common applications are materials for the textile industry, finishing materials for the automotive market and connection applications in indirect processes, eg before sheet welding.


We provide coating services on materials entrusted by the client but also specified by him, so we come to the policy of the adhesives used. Before proceeding to the implementation, however, we proceed to the initial production defining the detailed conditions and quality of the services provided. You will find out more about this in the open project tab ...

 

 

Sticky Stratum to nie tylko opis naszej oferty to także szereg liczb zebranych przez lata doświadczenia:

Miesięczny wolumen powlekania

125000 [m^2]

Doświadczenie naszej kadry

15 [lat]

Technologie powlekania i laminacji

12 [odmian]

Zasięg naszych produktów

27 [krajów]

MAGAZYN GŁÓWNY

ADRES:

ul. Rzepakowa 2a

40-547, Katowice

Polska

MOBILE:

+48 605 90 90 46

+48 512 327 035

WEB: www.stickystratum.com
MAIL: office@stikcystratum.com

 

GODZINY OTWARCIA

Poniedziałek 08:00 - 16:00
Wtorek 08:00 - 16:00
Środa 08:00 - 16:00
Czwartek 08:00 - 16:00
Piątek 08:00 - 16:00
Sobota ZAMKNIĘTE
Niedziela ZAMKNIĘTE